表紙画像

Orientation of carbon fibers in copper matrix produced by powder injection molding

Fiber orientation is a big challenge in short fiber reinforced composites. Powder injection molding (PIM) process has some intrinsic fiber alignment associated with it. During PIM process fibers in skin region of moldings are aligned as these regions experience higher shear flow caused by the mold w...

保存先:

書誌詳細
主要な著者:	Irfan Shirazi, M., Ahmad, F., Rafi Raza, M., Muhsan, A.S., Omer, M.A., Aslam, M.
フォーマット:	Conference or Workshop Item
出版事項:	EDP Sciences 2014
オンライン･アクセス:	https://www.scopus.com/inward/record.uri?eid=2-s2.0-84904965498&doi=10.1051%2fmatecconf%2f20141304027&partnerID=40&md5=d7747fdc779da71273da9597d70ebc1b http://eprints.utp.edu.my/32289/
タグ:	タグ追加タグなし, このレコードへの初めてのタグを付けませんか!

類似資料

Orientation of Carbon Fibers in Copper matrix Produced by Powder Injection Molding
著者:: ., M Irfan Shirazi, Faiz Ahmad, M Rafi Raza, Ali S Muhsan, MA Omer,
出版事項: (2014)

Shear controlled alignment of short carbon fibers in copper matrix composite green samples produced by powder injection molding
著者:: ., Irfan Shirazi, Faiz Ahmad, M Rafi Raza, Ali S Muhsan, M Aslam
出版事項: (2015)

Shear controlled alignment of short carbon fibers in copper matrix composite green samples produced by powder injection molding
著者:: Shirazi, I., 等
出版事項: (2015)

Effects of mold geometry on fiber orientation of powder injection molded metal matrix composites
著者:: Ahmad, F., 等
出版事項: (2015)

THERMAL CONDUCTIVITY OF POWDER INJECTION MOLDED CARBON NANOTUBE-REINFORCED COPPER-MATRIX COMPOSITES
著者:: ., Ali Samer Muhsan, Faiz Ahmad, Norani M Mohamed, M Rafi Raza
出版事項: (2015)

Thermal conductivity of powder injection molded carbon nanotube-reinforced copper-matrix composites
著者:: Muhsan, A.S., 等
出版事項: (2015)

FIBER ORIENTATION IN METAL INJECTION MOLDED SHORT CARBON FIBER REINFORCED COPPER MATRIX COMPOSITE
著者:: SHIRAZI, MUHAMMAD IRFAN
出版事項: (2014)

FIBER ORIENTATION IN METAL INJECTION MOLDED SHORT CARBON FIBER REINFORCED COPPER MATRIX COMPOSITE
著者:: SHIRAZI, MUHAMMAD IRFAN
出版事項: (2015)

PREPARATION AND FIBER FRACTURE OF METAL MATRIX COMPOSITE FEED-STOCK FOR POWDER INJECTION MOLDING.
著者:: ., Faiz Ahmad, Muhammad Rafi Raza, Ali Samer Muhsan, Mohd Afian Ome
出版事項: (2013)

Development of defects free stainless steel parts using powder injection molding
著者:: Muhammad Rafi Raza, Faiz Ahmad, M.A Omar, Ali S. Muhsan,
出版事項: (2017)

Rheological behavior of carbon nanotubes/copper feedstocks for metal injection molding
著者:: ., Faiz Ahmad, Ali Samer Muhsan, M Rafi Raza
出版事項: (2012)

Flow behavior of Cu/CNTs feedstocks for powder injection molding
著者:: ., li Samer Muhsan, Faiz Ahmad, Norani Muti Mohamed, M Rafi Raza
出版事項: (2011)

Powder injection molded nano copper oxide grafted graphene reinforced copper matrix composites
著者:: Naseer, A., 等
出版事項: (2022)

Carbon Nanotubes Reinforced Copper Matrix Nanocomposites via Metal Injection Molding Technique
著者:: ., Ali S Muhsan, Faiz Ahmad, Norani M Mohamed, Putri SMBTM Yusoff,
出版事項: (2012)

Role of debinding to control mechanical properties of powder injection molded 316L stainless steel
著者:: ., Muhammad Rafi Raza, Faiz Ahmad, MA Omar, RM German, Ali S Muhsan
出版事項: (2013)

Effect of Thermal Cycling on Thermal Conductivity of Powder Injection Moulded MWCNT Reinforced Copper Matrix Composites
著者:: Ahmad, F., 等
出版事項: (2020)

Uniform dispersion of multiwalled carbon nanotubes in copper matrix nanocomposites using metal injection molding technique
著者:: ., Ali Samer Muhsan, Faiz Ahmad, Norani M Mohamed, Puteri Sri Melor
出版事項: (2013)

Effects of vanadium carbide on sintered WC-10%Co produced by micro-powder injection molding
著者:: Wong, Yee Ning, 等
出版事項: (2015)

Effects of Sintering Temperature and Cooling Rate on Mechanical Properties of Powder Injection Molded 316L Stainless Steel
著者:: Raza, M.R., 等
出版事項: (2012)

Control of defects in powder injection molded aluminum matrix composites
著者:: Ahmad, Faiz
出版事項: (2008)

Effects of debinding and sintering atmosphere on properties and corrosion resistance of powder injection molded 316 L - stainless steel
著者:: Raza, Muhammad Rafi, 等
出版事項: (2017)

Experimental Investigation on Thermal Conduction of Carbon Nanotubes Reinforced Copper Matrix Composites
著者:: ., Faiz Ahmad, Muhammad Aslam, M Rafi Raza, Ali S Muhsan
出版事項: (2014)

Flow induced fiber orientation in short carbon fiber reinforced copper matrix composites
著者:: Ali, S., 等
出版事項: (2022)

Defect Analysis of 316LSS during the Powder Injection Moulding Process
著者:: ., M Rafi Raza, Faiz Ahmad, MA Omar, RM German, Ali S Muhsan
出版事項: (2012)

Effects of debinding and sintering atmosphere on properties and corrosion resistance of powder injection molded 316 L - Stainless steel
著者:: Raza, M.R., 等
出版事項: (2017)

Injection Molded Short-Carbon Fiber Reinforced Silicon Matrix Composites
著者:: Ahmad, Faiz, 等
出版事項: (2007)

Low pressure injection molding of boron admixed 316l stainless steel for engineering applications
著者:: Aslam, M., 等
出版事項: (2016)

A Study of Physical and Mechanical Properties of Powder Injection Molded Copper-Tungsten Alloys
著者:: Shanmugam, Kashinath
出版事項: (2018)

Grafting Of Metal Oxides On Graphene Nanoplatelets For Copper Composites Via Powder Injection Molding
著者:: Naseer, Abqaat
出版事項: (2019)

Carbon nanotubes reinforced copper matrix nanocomposites via metal injection molding technique
著者:: Faiz Ahmad ,, 等
出版事項: (2012)

Numerical Simulation of Fibre Orientation in Simple Injection Molding Processes
著者:: Oumer, A.N., 等
出版事項: (2009)

Determination of Critical Powder Loading of Titanium-Hydroxyapatite with Powder Space Holder for Powder Injection Molding Feedstocks / Mohd Yusuf Zakaria...[et al.]
著者:: Zakaria, Mohd Yusuf, 等
出版事項: (2017)

Nanoscale dispersion of carbon nanotubes in copper matrix nanocomposites for thermal management applications
著者:: ., Ali Samer Muhsan, Faiz Ahmad, Norani M Mohamed, M Rafi Raza
出版事項: (2013)

Powder Injection Molding of Modified 316L Stainless Steel for Dental Implant Application
著者:: ASLAM, MUHAMMAD
出版事項: (2016)

Numerical Prediction of Flow Induced Fibers Orientation in Injection Molded Polymer Composites
著者:: A. N., Oumer, 等
出版事項: (2015)

Fabrication and Microstructural Analysis of CNTs Reinforced Copper Matrix Nanocomposites via MIM Technique
著者:: ., Ali Samer Muhsan, Faiz Ahmad, Norani M Mohamed, M Rafi Raza
出版事項: (2013)

Ball milling of WC-CO powder as injection molding feedstock
著者:: M. Amin, Sri Yulis, 等
出版事項: (2012)

Effect of space holders on fabrication of porous titanium alloy-hydroxyapatite composite through powder injection molding
著者:: Farrahshaida Mohd Salleh,, 等
出版事項: (2017)

Particle size and injection temperature effect on the injection molding of SS316l powder
著者:: Jamaludin, Khairur Rijal, 等
出版事項: (2008)

Fabrication of high magnetic performance Feâ��50Ni alloy by powder injection molding
著者:: Ali, M., 等
出版事項: (2020)