表紙画像

Performance evaluation of three phase induction motor using rotor frame 0.35 mm and 0.50 mm of non-oriented steel sheets

In this project, the three phase AC induction motor have been thoroughly investigated and analyzed in terms of the induction motor parameter, efficiency, power factor and loss segregation. Throughout this project, the performance of the three phase induction motor when it design and modeling by usi...

保存先:

書誌詳細
第一著者:	Yanawati, Yahya
フォーマット:	学位論文
言語:	English
出版事項:	Universiti Malaysia Perlis (UniMAP) 2014
主題:	Induction motor Efficiency Electric motors, Induction lectric motors, Induction > Design and construction
オンライン･アクセス:	http://dspace.unimap.edu.my:80/dspace/handle/123456789/33133
タグ:	タグ追加タグなし, このレコードへの初めてのタグを付けませんか!

類似資料

Design of 0.5 hp induction motor rotor bars with 0.35 mm and 0.50 mm thickness of steel sheets for rotor fabrication
著者:: Yanawati, Yahya
出版事項: (2016)

Power factor performance on 0.35 mm and 0.50 mm thicknesses of steel sheets for 0.5 Hp induction motor using FEM software
著者:: Yanawati, Yahya, 等
出版事項: (2014)

In house construction of an induction motor rotor by using 0.35mm thickness of steel sheet for efficiency based investigation
著者:: Ismail, Daut, Prof. Dr., 等
出版事項: (2012)

Effect of different size of rotor bars on induction motor efficiency
著者:: Pungut, Ibrahim, 等
出版事項: (2012)

Load test of 0.5HP AC induction motor using coupling system
著者:: Ting, Siu Hui
出版事項: (2015)

Effect of rotor bar size on three phase induction motor performance
著者:: Pungut, Ibrahim
出版事項: (2014)

An innovative approach for energy conservation in induction motor
著者:: Chandrasekaran, V., 等
出版事項: (2009)

Design and development of single phase AC induction motor using copper rotor bars
著者:: Syatirah, Mohd Noor
出版事項: (2012)

Speed control of induction motor using fuzzy
著者:: Mohd Nazimudin, Ibrahim
出版事項: (2019)

Parameters calculation of 5 HP AC induction motor
著者:: Ismail, Daut, 等
出版事項: (2009)

Fabrication and investigation of copper rotor bar on 0.5HP induction Motor-A performance and economical study
著者:: Ismail, Daut, Prof. Dr., 等
出版事項: (2012)

Loss prediction of induction motor using OPERA 2D software
著者:: Ismail, Daut, Prof. Dr., 等
出版事項: (2012)

Analysis and design of induction motor applying Matlab
著者:: Mohd Azfitry, Zolkhifly
出版事項: (2009)

Copper rotor development process of induction motor
著者:: Ismail, Daut, Prof. Dr., 等
出版事項: (2012)

Application of D-STATCOM to mitigate high inrush current during start-up of three-phase induction motor
著者:: Ayob Nazmy, Nanyan
出版事項: (2019)

Investigation on 50-60 pieces 0.5HP induction motor efficiency based on no load, block rotor and DC resistance test
著者:: Tan, Chee Siang
出版事項: (2015)

Development of new stator for AC induction motor
著者:: Nadhirah, Che Abdullah
出版事項: (2015)

Development of New Copper Rotor for AC Induction Motor
著者:: Siti Fatimah, Shabbir Ahmad
出版事項: (2013)

Control design of forward-reverse induction motor
著者:: Adilah, Mansor
出版事項: (2009)

Design, build and evaluate an induction generator
著者:: Mohd Hafiz Arshad
出版事項: (2009)

Comparative study of motor high inrush current mitigation by improvisation of soft starter firing angle using PSCAD
著者:: Siti Izyan, Md Zaini
出版事項: (2017)

Design guidelines for recycling of rotating machines
著者:: Ismail, Daut, 等
出版事項: (2008)

Predicting an investigation of flux distribution in three phase induction motor stators by using different stator slot sizes
著者:: Nor Shafiqin, Shariffuddin, 等
出版事項: (2012)

Performance comparison different thickness of non oriented electrical steel material using analysis and performance chart from FEM software
著者:: Yanawati, Yahya, 等
出版事項: (2012)

Comparison of flux density between different thicknesses of non oriented electrical steel material using FEM software
著者:: Yanawati, Yahya, 等
出版事項: (2012)

Development of soft starter for single phase ac induction motor
著者:: Mohd Shafiq, Bahari
出版事項: (2014)

Pre determination of performance of double winding induction motor using MATLAB
著者:: Chandrasekaran, V., 等
出版事項: (2012)

Simulation of Three-Phase Induction Motor Control Using Fuzzy Logic Controller
著者:: Omar Said, Algayash Bennanes
出版事項: (2004)

Predicting the localized flux distribution in three phase induction motor between different stator slot size
著者:: Ismail, Daut, Prof. Dr., 等
出版事項: (2011)

Design and measurement of losses in AC induction motor with different rotor bar material
著者:: Gomesh Nair, Shasidharan
出版事項: (2010)

Single-Phase induction motor performance with Symmetrical AC supply
著者:: Muhammad Sukri Ngatiman
出版事項: (2009)

Analysis Of Wireles Power Transfer System
著者:: Devaraj PillaiVignesvaran
出版事項: (2023)

Effect of Voltage Sag and Mitigation on induction motor behavior
著者:: Ahmad Farris, Sha’ri
出版事項: (2013)

Induction motor behavior due to unsymmetrical and symmetrical faults
著者:: Surya, Hardi, 等
出版事項: (2012)

The effect of different stator slot size on flux and losses distribution in 0.5 hp induction motor
著者:: Nor Shafiqin, Shariffuddin
出版事項: (2014)

Induction motor behavior due to symmetrical and un-symmetrical faults
著者:: Ismail, Daut, Prof. Dr., 等
出版事項: (2013)

Effect of symmetrical voltage sags on induction motor and comparison solutions
著者:: Zaid, Mohd Zaini Makhtar
出版事項: (2013)

Non-invasive jaundice measurement using magnetic induction spectroscopy technique
著者:: Jurimah, Abd Jalil
出版事項: (2017)

Development of Single Phase Induction Motor Adjustable Speed Control Using M68HC11E9 Micro controller
著者:: Hussien, Hamad Saad
出版事項: (2004)

Modeling and validation of brushless DC motor
著者:: Mohd Sabri, Hussin, 等
出版事項: (2011)