Search Results - (( simulation optimisation system algorithm ) OR ( parameter evaluation method algorithm ))
Search alternatives:
- simulation optimisation »
- parameter evaluation »
- optimisation system »
- system algorithm »
- method algorithm »
-
1
PID-based control of a single-link flexible manipulator in vertical motion with genetic optimisation
Published 2009“…The important point is to evaluate the range of PID parameter which used in the GAs programmed to find the best value of this parameter. …”
Get full text
Get full text
Get full text
Proceeding Paper -
2
Sensorless Adaptive Fuzzy Logic Control Of Permanent Magnet Synchronous Motor
Published 2008“…The design and optimisation of the FLC are carried out using an adaptive fuzzy inference system network that uses the backpropagation, least square and gradient algorithms. …”
Get full text
Get full text
Thesis -
3
Modelling and calibration of high-pressure direct injection compressed natural gas engine
Published 2021“…A proper setting for the MBC procedure using the Genetic Algorithm (GA) needs to be identified. The objectives of the study are 1) to analyse the effect of HPDI-CNG system configuration and influential parameters, 2) to evaluate the injector mass flow rate and its suitability to fulfil engine requirement, 3) to assess the HPDI-CNG vehicle performance as a whole, and 4) to calibrate the electronic control unit (ECU) base maps by using MBC procedure. …”
Get full text
Get full text
Thesis -
4
Modelling of optimized hybrid debris flow using airborne laser scanning data in Malaysia
Published 2019“…Cuckoo search), and evaluator or model inducing algorithms (e.g SVM) were utilized for feature subset selection, which further compared to select the optimal conditioning factors subset. …”
Get full text
Get full text
Thesis -
5
Hybrid firely and particle swarm optimisation algorithm for optimal dimming level and energy saving in lecturer’s room
Published 2022“…To achieve the optimisation, a good, efficient and fast simulation algorithm is required. …”
Get full text
Get full text
Get full text
Get full text
Thesis -
6
Optimisation of automatic generation control performance in two-area power system with pid controllers using mepso / Lu Li
Published 2018“…From the simulation results, it was found that with the same number of PID controllers, the performance of AGC optimised by using MEPSO-TVAC algorithm is better in terms of overshoot and fitness value than using EPSO and PSO algorithms. …”
Get full text
Get full text
Get full text
Thesis -
7
FPGA implementation of simulated kalman filter optimization algorithm
Published 2018“…This paper presents a novel FPGA implementation of the Simulated Kalman Filter Optimisation Algorithm. This system utilizes a distributed RAM to update the intermediate variables and the output of each iteration is stored in the block RAM. …”
Get full text
Get full text
Get full text
Article -
8
ENGINEERING DESIGN WITH PSO ALGORITHM
Published 2019“…Creating a PSO algorithm-based infrastructure integrating with the recommendation system will further enhance solution to the design problem. …”
Get full text
Get full text
Final Year Project -
9
Modelling and Control of Ankle Foot Orthosis (AFO) for Children Utilising Soft Computing Towards Intelligent Approach
Published 2024“…Using data immediately obtained from the experimental setup, the system's dynamic behaviour was simulated. The research uses both non-parametric and parametric techniques, namely Multilayer Perceptron Neural Network (MLP NN) and Particle Swarm Optimisation (PSO), for system modelling. …”
Get full text
Get full text
Get full text
Get full text
Thesis -
10
Smart grid: Bio-inspired algorithms energy distributions for data centers
Published 2025“…This project proposes and evaluates three bio-inspired and evolutionary algorithms for VM allocation and migration: Ant Colony Optimisation (ACO), Particle Swarm Optimisation (PSO), and a Modified Genetic Algorithm (MGA). …”
Get full text
Get full text
Final Year Project / Dissertation / Thesis -
11
Genetic algorithm optimisation for fuzzy control of wheelchair lifting and balancing
Published 2009Get full text
Get full text
Get full text
Proceeding Paper -
12
-
13
Develpoment of combinatorial optimisation for cutting tool path strategy
Published 2009“…This work aims to optimise the tool path by simulating the removal of material in a finite element environment, which is controlled by a Genetic Algorithm. …”
Get full text
Get full text
Conference or Workshop Item -
14
Optimised intelligent tilt controller scheme using genetic algorithms
Published 2006“…The objective function for the GA procedure was based on a performance index combining the system response on curved and straight track. Simulation results illustrate the effectiveness of the scheme compared to the conventional nulling-tilt approach.…”
Get full text
Get full text
Get full text
Conference or Workshop Item -
15
Augmented model based double iterative loop techniques for integrated system optimisation and parameter estimation of large scale industrial processes
Published 1993“…The methods incorporate integrated system optimisation and parameter estimation which utilizes process measurements to achieve real process optimality inspite of model reality differences. …”
Get full text
Get full text
Article -
16
Evolvable traffic signal control for intersection congestion alleviation with enhanced particle swarm optimisation
Published 2017“…This work simulates traffic system and develop an optimising algorithm to instruct the traffic signal timing plan. …”
Get full text
Get full text
Get full text
Get full text
Proceedings -
17
-
18
Optimization of zinc oxide surge arrester design in reducing leakage current / Nurul Ain Abdul Latiff
Published 2018“…Evolutionary computation methods, imperialist competitive algorithm (ICA) and gravitational search algorithm (GSA) were employed to optimise the arrester designs, which can minimise the leakage current. …”
Get full text
Get full text
Get full text
Thesis -
19
-
20
An experimental validation and optimisation tool path strategy for thin walled structure
Published 2011“…This work was carried out with the aim to optimise the tool path by simulating the removal of material in a finite element environment which is controlled by a genetic algorithm (GA). …”
Get full text
Get full text
Get full text
Article
